|
|
|
|
|
|
|
POLYLINE™ comes standard with "industry exclusive" multi-mounting capability including an out-of-the-box mounting flange or adjustable mounting feet which adapt to various mounting configurations. Featuring metallic or nonmetallic lathes and molded-in latch keepers and mounting bosses, a tongue and groove seal joint between cover and base POLYLINE™ is the ultimate in polycarbonate enclosures. A clear polycarbonate cover option is also available for instrumentation applications where critical electronic equipment must be visible and protected from the elements.
Cover to base design - flush, aesthetically pleasing and more modern architecture
- Clear polycarbonate instrumentation cover where critical Electrical / Electronic equipment must be visible and protected from the elements
- Solid / opaque covers available as an additional option
|
|
| |
Option "F" Out-of-Box
Factory Installed Flange
Standard
4 Separate Bagged Feet
|
Patented multi-mounting capability
- Out-of-the-box lange design - factory installed
- Optional foot mount brackets for multi-directional mounting (vertical or horizontal positioning)
- Mounting dimensions molded into the enclosure base
- Durable polycarbonate feet/flanges resist cracking during wall mount assembly
- Feet and flanges act as an enclosure pad on uneven surfaces preventing enclosure from being drawn down and binding
- Feet and flange pads also allow an air gap of barrier between the enclosure and a warm machine chassis or mounting wall to prevent over-heating
|
|
| |
|
|
|
-
Moulded hinge design with stainless steel tamper resistant hinge pin with no wall penetrations
-
Tongue and groove, closed cell neoprene seal design achieves NEMA Type 4X rating
|
|
|
|
| |
|
- Adjustable corner panel mounts for supporting the aluminum hinge front panel within the molded-in corner slots and provides either flush positioning with the box top or adjustability down in the box 1.5" deep
|
|
|
|
|
|
| |
|
|
|
| |
|
|
|
| |
|
|
|
| |
|
|
|
|
Summary of Product Options |
| |
Covers Available |
Cover Attachment Options |
Mount Options |
Base Number Size |
Size |
Opaque Cover (None) |
Clear Cover (CC) |
Screw Cover (None) |
Hinged Screw Cover (H) |
Hinged Nonmetal Latch
(NL) |
Hinged
Snap Latch
(L) |
Foot Mount (None) |
Flanged Mount
(F) |
AMP664 |
6X6X4 |
X |
X |
X |
X |
X |
X |
X |
X |
AMP864 |
8X6X4 |
X |
X |
X |
X |
X |
X |
X |
X |
AMP1084 |
10X8X4 |
X |
X |
X |
X |
X |
X |
X |
X |
AMP1206 |
12X10X6 |
X |
X |
X |
X |
X |
X |
X |
X |
AMP1426 |
14X12X6 |
X |
X |
X |
X |
X |
X |
X |
X |
|
| |
Polyline™ Physical Properties |
Enclosure material
Typical Properties |
ASTM Test Method |
Polycarbonate |
Cover Seal-Closed
Cell Neoprene |
Impact Strength (ft - lb/in) |
D256 |
12 |
- |
Flexural Strength (psi) |
D790 |
13,000 |
- |
Tensile Strength (psi) |
D638 |
9,000 |
1,500 |
Compressive Strength ( |
D695 |
11,000 |
- |
Water Absorption (%) |
D570 |
0.25 |
0.00 |
Specific Gravity |
D792 |
1.20 |
1.23 |
Shrinkage in/in |
D955 |
0.007 |
- |
Hardness (Barcol-Rockwell M-Shore A) |
D2583 |
75 |
45 |
Elongation (%) |
D638 |
7.00 |
350 |
Dielectric Strength (kV/in) |
D149 |
732 |
- |
Arc Resistance (sec) |
D495 |
117 |
- |
Flammability |
UL94 |
V-0 |
V-0 |
Heat Deflection (°F at 264 psi) |
0648 |
266 |
- |
Service Temperature (°F) |
- |
-31°F to 260°F |
-31°F to 225°F |
K Factor, Thermal Conductivity (BTU/hr/ft2/°F/in) |
D1269E |
1.25 |
- |
Thermal Expansion (10-6th in/in °F) |
D696 |
36 |
- |
UV Rating |
UL746C |
(f1) |
- |
|
|
| |
Certificate of Conformance to Industry Standards
Polyline™ Industrial enclosures manufactured by Allied Moulded Products, Inc. and bearing the UL® and CSA labels have been tested and certified to the following standards:
- UL 50 - enclosures For Electrical Equipment
- UL 50E - Enclosures For Electrical Equipment, Environmental Considerations
- UL 508A - Industrial Control Panels
- UL 746C - Polymeric Materials - Use in electrical Equipment Evaluations
- CSA-C22 No. 14 - Industrial Control Equipment
- CAN/CSA-C22 No. 94 - Special Purpose Enclosures
Allied Moulded Products AMP Series Polyline™ enclosures are certified:
- UL types 1, 2, 3, 4, 4X, 12 and 13
- CSA types 1, 2, 3, 3R, 4, 4X, 12 and 13
- NEMA types 1, 2, 3, 3R, 4, 4X, 12 and 13
|
| |
Typical Applications for Non-Metallic Enclosures:
- Car Wash Equipment
- Irrigation Systems
- Waste Water Treatment
- Poultry Processing Equipment
- Instrumentation
- SCADA Systems
- Marinas
- Pool and Landscape Lighting
- Agriculture
- Parking Lots and Garages
|
Please contact Cal-Centron for additional Information.
